SC & SCP BEARINGS FOR CONTINUOUS CASRING MACHINES

2021-06-15 12:41:46 liyulong126

rolling mill bearings, Roll neck bearings, Tapered roller bearings, Spherical roller bearings

•In continuous casting machines, roll support bearings are used under heavy loads and at extremely low speed. In addition, the operating conditions are severe, resulting in exposure to splashing water and scales.

•SCP bearings for fixed side and SC bearings for free side are used for end of rolls.

•HSC bearing units with half-round outer ring is used for the intermediate support section of beetle-shape rolls, such as driving rolls.

•FV bearings for continuous casting machines are designed based on a full complement cylindrical roller bearing, with reference to maximized static load ratings. Crowning are set up on rolling surface of its rollers, according to the size of loads, which contributes to solve stress concentration at specific location.

•The bearing has the self-aligning mechanism to absorb roll bending and misalignment due to heavy load.

SC bearings (free side)

rolling mill bearings, Roll neck bearings, Tapered roller bearings, Spherical roller bearings

SCP bearings (fixed side)

rolling mill bearings, Roll neck bearings, Tapered roller bearings, Spherical roller bearings

• To accommodate thermal contraction andexpansion of roll, the inner ring of this bearingare designed to move smoothly in the axial direction.

• The bearing has been developed for the purpose of improvement in short service life of spherical roller bearings most commonly used for continuous casting machines.

• The ribs provided for the inner and outer rings and loose rib allow accommodation of axial loads generated by thermal contraction and expansion of rolls.

HSC bearing units with half-round outer ring

rolling mill bearings, Roll neck bearings, Tapered roller bearings, Spherical roller bearings

• To accommodate thermal contraction and expansion of roll, the inner ring and roller of this bearing are designed to move smoothly in the axial direction.

• This unit has unique structure, with a half-round outer ring placed on the loaded side only. • This special half-round outer ring and compact seal design realizes a 15 % increase in static load rating over that of conventional products.

• The unique jacket design adjusts the flow of water and enables a high cooling efficiency, equivalent to that of conventional products with a lower water flow rate of 55 %.

SC & SCP series bearings for continuous casting machines

(Cylindrical roller bearings with Aligning ring - Special bearings for CCM)

rolling mill bearings, Roll neck bearings, Tapered roller bearings, Spherical roller bearings

Bearing No.	Boundary dimensions(mm)				Acceptable roll	Basicloadratings		Mass	Mounting dimensions		Design	Corresponding Spherical Roller bearing
	Boundary dimensions(mm)				heat expansion	(kN)		Mass	(mm)Da.			Bearing No.	Basic load ratings(kN)
	d	D	B	rmin.	(mm)	C	Cor	(kg)	min.	max.		Bearing No.	Cr	Cor
SC101140VA	50	110	40	2	±4.5	164	254	2.1	96	99	1	22310RHR	204	237
SC119032VA	55	90	32	1.1	±3.5	89.9	202	0.9	81	82	1	—	—	—
SC111025VA	55	100	25	1.5	±4	95.9	143	0.9	93	93	1	22211RHR	124	144
SC131231V-1A	65	120	31	1.5	±4	118	206	1.7	110	111	1	22213RHR	178	211
SC131448VA	65	140	48	2.1	±5.5	238	393	4	123	127	1	22313RHR	305	360
SC141331VA	70	125	31	1.5	±6	126	213	1.8	116	117	1	22214RHR	187	222
SC141551VA	70	150	51	2.1	±7.5	273	406	4.7	132	137	1	22314RHR	348	413
SC151331VA	75	130	31	1.5	±5	148	237	1.9	120	121	1	22215RHR	193	236
SC171565VA	85	150	65	3	±8	280	621	5.4	129	137	1	24217RHB	370	558
SCP171565VA	85	150	65	3	—	280	621	5.5	129	137	2	24217RHB	370	558
SC181640-1VA	90	160	40	2	±4.5	240	427	3.8	147	149	1	22218RHR	298	381
SCP181640V-1A	90	160	40	2	—	194	400	3.9	147	149	2	22218RHR	298	381
SC181652VA	90	160	52.4	2	±5.5	309	555	4.9	144	148	1	23218RH	336	482
SCP181652V-2A	90	160	52.4	1.1	—	271	566	5.1	144	148	2	23218RH	336	482
SC181645/48V-1A	90	160	45/48	2	±5.5	249	507	4.4	147	150	1	—	—	—
SC201550VA	100	150	50	1.5	±6	232	543	3.4	137	139	1	—	—	—
SCP201550VA	100	150	50	1.5	—	232	543	3.4	137	139	2	—	—	—
SC201752V-1A	100	165	52	2	±5.5	279	600	4.8	149	153	1	23120RH	328	510
SC211656VA	105	160	56	2	±9	242	594	4.4	144	149	1	24021RHA	317	550
SC221745V-3A	110	170	45	2	±5.5	260	523	4	158	160	1	23022RH	300	486
SCP221745V-3A	110	170	45	2	—	260	523	4.1	158	160	2	23022RH	300	486
SC221760V-1A	110	170	60	2	±8	279	722	5.5	152	157	1	24022RH	375	647
SC221764VA	110	170	64	2	±10	279	722	5.8	151	157	1	—	—	—
SC221856V-8A	110	180	56	2	±7.5	296	667	6.1	162	167	1	23122RH	385	605
SC221869V-3A	110	180	69	2	±9	355	842	7.6	157	164	1	24122RH	469	778
SCP221869V-3A	110	180	69	2		355	842	7.8	157	164	2	24122RH	469	778
SCP222053VA	110	200	53	2.1	—	333	626	8.2	182	187	2	22222RHR	491	642
SC241846V-2A	120	180	46	2	±6	231	588	4.5	168	170	1	23024RH	314	524
SCP241846V-2A	120	180	46	2	_	231	588	4.6	168	170	2	23024RH	314	524
SC241854VA	120	180	54	2	±12	246	516	5	165	169	1	_	_	_
SC241858V-1A	120	180	58	2	±8	274	726	5.7	164	168	1	_	_	_
SC241860V-1A	120	180	60	2	±9	274	726	5.8	163	168	1	24024RH	397	709
SC241856/46VA	120	180	56/46	2	±10	279	626	5.2	165	169	1	_	_	_
SC242080VA	120	200	80	2	±9.5	521	1120	11.1	174	183	1	24124RH	605	1020
SCP242080V-3A	120	200	80	2	_	431	1040	12	174	183	2	24124RH	605	1020
SCP262052V-1A	130	200	52	2	_	295	701	6.7	186	189	2	23026RH	404	674
SC262069V-1A	130	200	69	2	±9	381	969	8.7	179	186	1	24026RH	512	914
SCP262069V-1A	130	200	69	2	_	381	969	8.9	179	186	2	24026RH	512	914
SC262079/69VA	130	200	79/69	2	±11	443	1090	9.6	177	185	1	_	_	_
SC262164VA	130	210	64	2	±10	408	882	9.2	190	196	1	23126RH	494	799
SC262180V-2A	130	210	80	2	±11.5	448	1120	11.9	184	193	1	24126RH	620	1080
SCP262180V-2A	130	210	80	2	_	448	1120	12.2	184	193	2	24126RH	620	1080
SC262364V-2A	130	230	64	3	±9	442	950	12.5	209	215	1	22226RHR	658	914
SC282153V-1A	140	210	53	2	±6	331	834	7.1	195	199	1	23028RH	422	723
SCP282153V-1A	140	210	53	2	_	331	834	7.2	195	199	2	23028RH	422	723
SC282169RVA	140	210	69	2	±9.5	431	1010	8.8	191	196	1	24028RH	524	957
SCP282169RVA	140	210	69	2	_	431	1010	9.3	191	196	2	24028RH	524	957
SC282368RVA	140	225	68	2.1	±7	512	1150	11.1	204	210	1	23128RH	565	940
SCP282368V-1A	140	225	68	2.1	_	465	1020	11.6	204	210	2	23128RH	565	940
SC282385V-1A	140	225	85	2.1	±11.5	521	1300	14.4	199	208	1	24128RH	702	1220
SCP282385V-1A	140	225	85	2.1	_	521	1300	14.8	199	208	2	24128RH	702	1220
SC302375V-6A	150	225	75	2.1	±9	492	1220	11.4	203	209	1	24030RH	593	1100
SCP302375V-6A	150	225	75	2.1	_	492	1220	11.8	203	209	2	24030RH	593	1100
SC3025100V-1A	150	250	100	2.1	±14	666	1650	21.9	218	230	1	24130RH	915	1590
SC302796VA	150	270	96	3	±12	806	1670	26.2	236	247	1	23230RH	959	1540
SC322480-2VA	160	240	80	2.1	±13	542	1280	13.6	216	225	1	24032RH	679	1270
SC3227109VA	160	270	109	2.1	±13.5	867	1980	28	233	247	1	24132RH	1070	1890
SC3234114VA	160	340	114	4	±15	1230	2300	55.3	303	316	1	22332RHA	1420	1940
SC342690V-1A	170	260	90	2.1	±14	622	1560	18.7	232	241	1	24034RH	828	1540
SCP342690V-1A	170	260	90	2.1	—	622	1560	19.1	232	241	2	24034RH	828	1540
SC3431110VA	170	310	110	4	±14	1010	2180	40.1	270	285	1	23234RHA	1210	1940
SC3628100V-1A	180	280	100	2.1	±14	743	1890	25	248	260	1	24036RH	984	1830
SC3632112V-1A	180	320	112	4	±15	950	2350	43.5	280	295	1	23236RHA	1320	2170
SCP3632112V-1A	180	320	112	4	—	950	2350	44.1	280	295	2	23236RHA	1320	2170
SCP382975V-1A	190	290	75	2.1	—	595	1530	20.3	268	274	2	23038RHA	789	1430
SC3829100V-1A	190	290	100	2.1	±14	768	2030	26.1	259	269	1	24038RHA	1010	1920
SCP3829100V-1A	190	290	100	2.1	—	768	2030	26.8	259	269	2	24038RHA	1010	1920
SC3832104VA	190	320	104	3	±12	1030	2270	37.2	288	298	1	23138RHA	1210	2080
SC3832128VA	190	320	128	4	±15.5	1120	2790	46.7	278	293	1	24138RHA	1460	2630
SCP3832128VA	190	320	128	4	—	1120	2790	47.8	278	293	2	24138RHA	1460	2630
SC3834120V-1A	190	340	120	4	±16	1110	2720	53	301	315	1	23238RHA	1490	2470
SCP403182VA	200	310	82	2.1	—	692	1810	25.9	282	291	2	23040RHA	940	1680
SC403111RVA	200	310	109	2.1	±11	978	2550	33.5	273	286	1	24040RHA	1180	2230
SC4034112V-1A	200	340	112	3	±16	1080	2490	46	304	317	1	23140RHA	1380	2340
SC4034140VA	200	340	140	3	±19	1350	3090	56.1	292	313	1	24140RHA	1660	2970
SC4437150VA	220	370	150	4	±19	1540	3750	72.3	320	340	1	24144RHA	1920	3550

HSC bearing units with half-round outer ring for continuous casting machines[2021/06/15]

SC & SCP BEARINGS FOR CONTINUOUS CASRING MACHINES

HSC bearing units with half-round outer ring for continuous casting machines[2021/06/15]

News

Recommended content